DIY Solar Cells Ardmore OK

This page provides useful content and local businesses that can help with your search for Solar Cells. You will find helpful, informative articles about Solar Cells, including "Solar4Scholars: Make Your Own Solar Cell". You will also find local businesses that provide the products or services that you are looking for. Please scroll down to find the local resources in Ardmore, OK that will answer all of your questions about Solar Cells.

D & J Hardware and Building Supply
(580) 657-3264
Highway 70 W
Lone Grove, OK
 
Fastenal- Ardmore
580-226-5083
615 West Broadway Ardmore, OK, 73401
Ardmore, OK
 
3 Armore Mall
(580) 223-5700
320 N Commerce St
Ardmore, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12-17
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12-17

Lumbermen's Millwork
(580) 223-3080
2211 Refinery Rd
Ardmore, OK
 
Cooper True Value Auto Stores
(580) 369-3371
207 E Main St
Davis, OK
 
County Building Center
(580) 226-1208
821 West Main
Ardmore, OK
 
Lowe's
(580) 490-3430
2701 12Th Avenue Nw
Ardmore, OK
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF ARDMORE, OK
580 490-3430
2701 12TH AVENUE NW ARDMORE, OK, 73401
Ardmore, OK
 
Lone Grove True Value
(580) 657-3339
406 Case Circle
Ardmore, OK
 
Gordon White Lumber
(580) 369-3119
405 E Main
Davis, OK
 

Solar4Scholars: Make Your Own Solar Cell

You will need:

  • A small (2' x 1') sheet of copper flashing (available at your local hardware store)
  • An electric stove (a propane torch may also be used)
  • A large clear plastic bottle
  • Table salt
  • Tap water
  • Sandpaper (or steel wool)
  • Sheet metal shears (also called "tin snips")
  • Two alligator clip leads
  • A micro-ammeter (available from Radio Shack or other electronics store)

Instructions: How to build a solar cell

  1. Cut the piece of copper sheeting, so that it fits the stove burner. Clean it first, so that there is no corrosion or other materials. Use the sandpaper.
  2. Heat the copper sheeting until it is red hot. This will create two kinds of copper oxide: cuprous oxide is the one you are interested in. It will be red or tinges of orange or pink. This will be found underneath the black cupric oxide (which is no use to us). These copper oxides will begin to form after only a few minutes, but let the copper 'fry' for up to half an hour, forming a fairly thick coat of cupric oxide.
  3. Turn off the stove and let the copper flashing cool slowly. The copper will shrink as it cools, and some or most of the black cupric oxide will actually pop off. Remove the copper from the stove element, once it has cooled (after about 20 minutes).
  4. Lightly clean or rub the copper flashing with the sandpaper, under running tap water if you wish. Remove the cupric oxide but be sure to not remove much of the cuprous oxide.
  5. Cut another piece of copper about the same size as the first. Bend both pieces of copper and set them inside the jar or bottle, making sure they are not touching. Connect the two plates to the ammeter. Connect the plate with cuprous oxide to the negative terminal and the clean plate to the positive terminal. You now have a solar cell, with a charge being read on the micro-ammeter.

Test your panel

Take your solar cell out into the sunlight and watch the micro-ammeter jump. In shade, you will get very low micro-amperage, but in the su...

Click here to read more from The Solar Guide

About Us | Contact Us | Link to Us | Privacy Policy | Terms of Use | Resources | Sitemap